Industrial Plastic Moulded Products
incl. GST
In order to keep pace with the never-ending demands of customers, we are involved in offering a wide range of Industrial Plastic Moulded Products.
☰
In order to keep pace with the never-ending demands of customers, we are involved in offering a wide range of Industrial Plastic Moulded Products.
| Material | Plastic |
| Packaging Type | Box |
| Tensile Strength | 10 - 25 Mpa |
| Tolerance | 0.1 - 3.5 mm |
| Surface Finish | Coated |
In order to keep pace with the never-ending demands of customers, we are involved in offering a wide range of Industrial Plastic Moulded Products.
Walkie Talkie Battery.
...
Product DescriptionNEXO FIXX 630 is a general purpose industrial grade Cyanoacrylate adhesive with fast setting ,High flow ability and good penetration characteristics .It has been specially formulated to achieve the strongest possible bond between well - mated, Non porous surface. Such as rubber, metal, plastic. NEXO FIXX 630 is a one component system and does not require the catalyst, Heat or Clamps. When a thin layer of NEXO FIXX 630 is applied between two surfaces come in to contact with atmospheric moisture, a rapid polymerization occurs producing ultimate bond.
Curing PerformanceThere are many factors that can influence the rate of cure. These include: the type of substrate used, the condition of the surface to be bonded, the smoothness of the surface, the closeness of the surface, the atmospheric conditions like Humidity and Temperature.
Cure speed and Bond Gap (Filling between surfaces)The rate of cure depends on the Bond Gap (Gap between tow joined surfaces)simply smaller Bang gap faster speed of cure.
Direction for Useï‚· Make sure that the surface to be bonded are clean and dry( Preferable to solvent- wipe plastic,glass,rubber and acid treat to Metalsï‚· Dispense a Drop / Drops to one surface only. Apply only enough to leave a thin film after compression.ï‚· Press Parts Together and hold firmly for few seconds. Good Contact is essential. An Adequate bond develop in less than one minute ( Maximum strength achieved in 24 to 48 Hours)ï‚· Wipe off the excess of adhesive from top of container and recap NEXO FIXX 630 if left uncapped may deteriorate by contamination from moisture in the air.ï‚· Because NEXO FIXX 630 condenses by polymerization sometime whitening will occur on the surface of the container or the bonded material. Should this happen. Wipe surface with acetone.
7) Handling and StorageStorage Keep Product in unopened container in cool and dry location.Best when stored at 2 to 8 °C Temp less than 2 °C can adversely affect product properties. Do not freez.Keep container closed to air tight till ready for use.Handling Material removed from Containers may contaminate during use. Do not pour back any material removed from container again to full / partial container misuse of product will void all warrantees.8) Precautions and safety Noteï‚· Use with proper ventilation, Avoid contact with skin and eyes.ï‚· In case of skin contact rinse with warm water or dissolve gradually with solvent like acetone or nitro methane, do not remove forcefully or pull, rub on hardly, allow it to release slowly after some time.ï‚· If adhesive went in to eye, Keep eye open and rinse thoroughly. Seek medical attention immediatelyï‚· Keep well out of rich of children’sï‚· Keep adhesive in cool, Dry place 20 to 25°C( 68 to 77°F), for long time storage 2 to 35°C is preferred
lit (lifepo4) series is a complete range of 12v lifepo4 (lithium ion phosphate) battery products, for a wide variety of applications, such as ups, renewable energy system, inverter etc. The features (high energy density, high efficiency cells, less weight, eco-friendly, fast charging & long life) needed for these applications battery are all covered by our waaree ess lit series.
· lifepo4 (lithium iron phosphate) battery · outstanding cycle performance · excellent recharge acceptance · horizontal installation position for less space · low self-discharge rate · innovative robust design
|
battery |
12. 8v 6ah |
12. 8v 12ah |
12. 8v 18ah |
12. 8v 24ah |
12. 8v 30ah |
12. 8v 48ah |
|
12. 8v 60ah |
12. 8v 80ah |
12. 8v 100ah |
12. 8v 120ah |
12. 8v 160ah |
|
BEstablished in the year 2011at mumbai, Maharashtra, we “IB EXPORT" are a Sole Proprietorship company based firm, engaged as the foremost Manufacturer of Tungsten Copper Bar, Tungsten Copper Electrode, etc. Our products are high in demand due to their premium quality and affordable prices. Furthermore, we ensure to timely deliver these products to our clients, through this we have gained a huge clients base in the market.
...
Delivering the latest product trends and industry news straight to your inbox
We’ll never share your email address with a third-party.