The automotive water pump bearings are exclusively fabricated and manufactured with precision to last longer. These bearings are primarily used in automotive water pumps. They basically consist of standard double row bearings and are available in two different designs.
The automotive water pump bearings are exclusively fabricated and manufactured with precision to last longer. These bearings are primarily used in automotive water pumps. They basically consist of standard double row bearings and are available in two different designs.
Locking Assemblies Series C-3011
CANTO-LOCK C-3011 Rigid Couplings are supplied ready for installation. The torque capacity of these devices is based on a coefficient of friction of 0.12 for lightly oiled screws, rings and shaft contact areas.
The clearances between the two shafts and inner ring [1] should be similar.
INSTALLATION
NOTE: Never tighten locking screws before shaft installation, as CANTO-LOCK C-3011 Coupling inner ring can be permanently deformed even at relatively low tightening torques.
1. Carefully clean and lightly lubricate with ordinary machine oil shafts and inner ring bore. It is important NOT to use Molybdenum Disulfide (e.g., Molykote, Never
Seeze or similar lubricants) for shafts lubrication, since it will greatly reduce the torque capacity of the connection.
2. Once coupling is centered over shaft ends, hand-tighten three (3) or four (4) equally spaced locking screws and make sure that outer collars [2] & [3] are parallel. Hand tighten remaining locking screws. Important: shaft engagement equal for both ends with gap not exceeding 5% of shaft diameter.
3. Use torque wrench and set it approximately 5% higher than specified locking screw tightening torque (Ts). Tighten locking screws in either a clockwise sequence, using approx. % (ie, 90%) turns (even if initially some locking screws require a very low tightening torque to achieve x turns) for several passes until % turns can no longer be achieved
4. Continue to apply overtorque for 1-2 more passes. This is required to compensate for a system-related relaxation of locking screws since tightening of a given screw will always relax adjacent screws. Without overtorquing an infinite number of passes would be needed to reach specified tightening torque
5. Reset torque wrench to specified torque (Ts) and check all locking screws. No screw should turn at this point, otherwise repeat step 4 for 1 or 2 more passes. It is not necessary to re-check tightening torque after equipment has been in operation.
Introduction to MicrowavesMicrowave Transmission Lines and WaveguidesMicrowave Components and their S-parametersMicrowave Tubes and CircuitsSemiconductor Microwave Devices and CircuitsRadar Systems
1st edition, by V. S. BagadIntroduction to Microwaves Microwave frequencies, Advantages of microwaves, General and industrial applications of microwaves Microwave Transmission Lines and Waveguides Transmission line equations and solutions, Reflection and transmission coefficient, Standing wave and standing wave ratio, Line impedance and admittance, Impedance matching, Using stub line, Application of smith chart in solving transmission line problems, Introduction to strip lines, Microstrip lines, Parallel strip lines, Coplanar strip lines, Shielded strip lines, Rectangular waveguides-Theory and analysis, Principle of circular waveguide. Microwave Components and their S-parameters Wave-guide tees, Magic tees, Wave-guide corners, Bends, Twists, Directional couples. circulators and isolators. S matrix and its applications in analyzing microwave components Microwave Tubes and Circuits Limitations of conventional tubes at UHF and microwave, Klystrons, Velocity modulation, Multicavity klystron, Reflex klystron, Traveling wave tube, Magnetron (Without derivations). Semiconductor Microwave Devices and Circuits Microwave transistors and integrated circuits, Varactor diodes, Steprecovery diodes, Parametric amplifiers, Tunnel diode and its applications, Gunn diode and its applications, IMPATT diode, TRAPATT diode, PIN diode, Schottky barrier diodes. Radar Systems Basic principle, Radar range equation : Powers and frequencies used in radar, basic pulsed radar system, Factors Influencing maximum range, Effect of noise, Display methods, Search and tracking radar systems, Moving target indicator (MTI), CW Doppler radar, Frequency modulated CW radar.Additional InformationEdition 1st editionPublisher Technical PublicationsISBN 9789350383056No. of Pages (Printed Book) 304
Belt Fastener is a flexible rubber splice that screws directly onto the belt. It uses specifically designed self-drilling, self-tapping screws that preserve the belt integrity by spreading the carcass threads without cutting them.
...
Price Range: 1000-3000 Rs/unit
Note: Prices are Vary as per Capacity.
Standalone Smoke Detectors are used for small areas such as small office, cabins, shops etc. It gives alarm from the unit in case of fire.
Delivering the latest product trends and industry news straight to your inbox
We’ll never share your email address with a third-party.